RUST LOCK  
MSDS Sheet

PICTURE 1PICTURE 2 | PICTURE 3

RUST LOCK Summary:

Designed to resist weathering that promotes rust, and to withstand acids, salts, petrochemical products and caustic materials

Encapsulates rust and corrosion forming an air tight and moisture proof barrier virtually eliminating future rust and corrosion

RUST LOCK Attributes:

Extremely tough/durable
     Abrasion and mechanical impact resistant
     Flexible and will not crack or peel from expansion and contraction during extreme temperature variations
     Resistant to continuous immersion in acids, salts, alkalis, oils, solvents and other refined chemicals

Encapsulate toxic materials
    EPA approved to encapsulate toxic materials, including lead based paint and asbestos, eliminating the need for expensive procedures to remove the toxic material.
    Applied to dry or wet surfaces

Protective Coating
    Applied to new surfaces to prevent future corrosion problems, and older surfaces over the existing corrosion to prohibit further corrosion
    Extremely weather resistant and UV resistant for long life in       adverse environments
    High temperature resistance, up to 392F

Easy to apply:

Roller, brush or spray application

One coat application that dries in 2 hours

Will penetrate and encapsulate up to 18 coats of other paint

RUST LOCK Cost Benefits:

Requires less preparation time with no expensive and dirty sandblasting requirements

Encapsulate toxic materials, including lead based paint and asbestos, eliminating the need for expensive procedures to remove the toxic material and its disposal

There’s no need to risk poisoning workers or contaminating the environment

Applied to new surfaces to prevent future corrosion problems,
and older surfaces to prohibit further corrosion reducing
repair cost.

Environmentally safe:

Without question the most effective versatile encapsulating and pore penetrating coating on the market

Protective coating savings will more than offset the cost of repair/replacing damage from corrosion or costly removal of    toxic material

Is ranked #1 in Field Testing against all other corrosion control coatings

Testing has shown life expectancy to be 25+ years

Eliminates need for costly sandblasting and grinding

Eliminates need for costly toxic waste removal

DESCRIPTION:

 RUST LOCK is a one-part polyurethane coating that combines with atmospheric moisture to cure. Upon curing, RUST LOCK provides a protective coating of superior adhesion, flexibility and abrasion/impact-resistance. It is resistant to chemical solvents and acid splash.
Originally designed for metal surfaces, RUST LOCK demonstrates excellent adhesion to wood, concrete, fiberglass and many other substrates. RUST LOCK is designed for the encapsulation of and adherence to tightly-bonded surfaces of lead-based and other toxic paints as well as rusted surfaces. This unique ability is accomplished by the curing mechanism of the base polymer. The coating (having a low initial viscosity) wets the rusty surface, penetrates to the foundation of the rust's origin where curing begins, and the polymer begins to swell, developing an interlocking network between the pores of the surface and the coating.
No pot life, no catalyzation, no two-part mixing. Can substitute for zinc-rich primer requiring no white sand-blasting. Can be applied over rusted surfaces after loose/flaking material is removed. High humidity quickens dry/cure cycle.

APPLICATION METHODS:

 Can power wash with solvent wipe down, light commercial blast, or power hand tool to remove loose flake and debris before applying. Can use power tool (within the guidelines of Clean Air Act) with vacuum to prep lead-based paints (as discussed at Steel Structures Painting Council--SSPC--meeting March 15-17 attended by EPA and NIOSH) before applying RUST LOCK over lead-based paints. Possible alternative to abatement of lead paints. Surfaces should be clean, dry and sound. Existing surface dirt, oil, tar, grease and film should be removed from surface by approved methods (TSP-Tri-Sodium Phosphate or equivalent) prior to application of RUST LOCK. MUST BE COMPLETELY DRY. IMPORTANT: Stir product thoroughly before using. (Methods: SSPC-SP-2, SP-3, SP-6, SP-7)
RUST LOCK can be applied slowly with soft bristle brush, roller or spray equipment. It should be applied evenly without buildup at the prescribed thickness. Overly thick application may cause surface bubbling from gassing. Apply in one-coat system using cross-hatch method (side-to-side, up and down over same area). CAUTION: Wear gloves and protective clothing. Extremely tough to clean off skin. Throw away brushes and rollers after use. Wear eye protection. *CLEAN UP IMMEDIATELY OR WILL RUIN EQUIPMENT. SOLVENT: Clean-up or reduction, use MEK or MIBK. If sprayed, keep solvent ready to clean equipment before breaks (lunch hour) or at conclusion of job. 

IMPORTANT:

 Wear skin and eye protection. Do not take internally. Avoid contact with eyes. If solution does come in contact with eyes, flush immediately with water and contact a physician for medical attention. Avoid prolonged contact with skin or breathing of spray mist. KEEP OUT OF REACH OF CHILDREN. This is a flammable liquid. Keep away from flame or fire or other sources of ignition. NOTE: If overcoating with any other paint products, do so within a 2-week time period of initial application of RUST LOCK.

FEATURES:

 USDA-approved (safe around foods)/Lead- & chromite-free
Solid By wgt.: 50% / By volume: 51.37% 
By pigment: 15.10% / By vehicle wgt.: 48%
5-8 wet mil coat, 2-4 dry mil (200 sq.ft./gal.)
Dry Time: 1 hour to touch; 2 hours to re-coat (Must be overcoated with self within 4 hours. May topcoat with other coatings if within 2 weeks).
May be used by itself without a top coat.
Excellent adhesion to wide variety of substrates. Attaches into the pores of metal or concrete and expands to lock in.
Cures by reacting to moisture in the air.
A portion of a container may be used and re-sealed for later use, if done so carefully. A skin will form on surface of product. Remove skin and use as directed.
Salt Spray Corrosion Test: 2000 hours / Rating Procedure B:9
(Key to Rating 0-10; 0=complete failure, 10=excellent)
Vehicle Type: Aromatic Polyurethane
Pigment Type: Aluminum / Shelf life: 1 year
Gloss: Low angular sheen
VOC -- Rating: 418 gram/ltr, California EPA (Table of Standards) maximum accepted VOC allowed is 500 grams/liter under the classification of: "Metallic pig- mented coatings"
Viscosity: 77F. = 59 KU / 320 centipoise
SAG test: 4 mils wft = 320 cps +/- 5% (viscosity)
Density: 9.18 lbs. per gallon
Impact-Resistance: 200+psi Front/160psi Back 
Abrasion-Resistance: ASTM (D4060) Graded 18, (excellent) 
Lead-Based Paint Approval: Tested and approved by ASTM 1795 for lead -based paint encapsulation for all local, state, federal agencies. 
Transmission of electrical currents: Can withstand 18 volts without disbonding. For underground pipes and tanks. 

LIMITED WARRANTY:

 Unless the manufacturer provides a written warranty of fitness for a particular use, the manufacturer's sole warranty is that the product, as supplied, will meet then current sales specifications and is specific only to return of product found to be defective upon opening of container within one year. Customer's exclusive remedy and Superior's sole liability for breach of warranty is limited to refund of the purchase price or replacement of any product shown to be other than as warranted and the manufacturer expressly disclaims any liability for incidental or consequential damages.

COVERAGE RECOMMENDATIONS:

 Non-Rusted, Metal, Fiberglass (as a primer) 200 sq.ft. over rusted surface/300 sq.ft. as primer
Wood, Concrete, Porous Substrates/Rusted Metal 200 sq.ft./gallon
Apply coating in 1 application, using the cross-hatch method (up & down, side-to-side)
Bridges and/or Encapsulation 100-150 sq.ft./gal. (use brush or roller on 1st coat)
Apply in two coats (3-4 mils) to four coats (5-6 mils), depending upon specification milage required

Copyright 2014 - ATP, LLC. - All rights reserved
110 ATP Drive, Albertville, AL 35951
800-999-1ATP or 800-999-1287
For Info -
email
Designed and Hosted by The Godel Group, 865-690-2662 www.Godel.com